WELCOME TO OUR BLOG

We're sharing knowledgein the areas which fascinate us the most
click

What Does 55x85 Mean on a Tapered Roller Bearing?

Di bearingoffer November 5th, 2026 10 visualizzazioni

Introduction: A 55x85 tapered roller bearing gives two useful size facts, but the technician still needs to know which surface each number measures and what the size chain leaves open.

When a bearing comes out of a transmission, differential, or axle assembly, the old part is often worn, greasy, and missing its label. A caliper reading of 55 mm and 85 mm gives a quick starting point, yet those two figures only describe two boundary surfaces. Reassembly decisions depend on matching each figure to a named surface, then checking the axial width and assembly height that complete the installed stack. The reading order below follows the shop action: measure the bore, measure the cup outside diameter, compare both with the published figures, then check the missing axial dimensions before the part goes back into the housing.

What the Two Numbers in 55x85 Measure on a Tapered Roller Bearing

In a size callout such as 55x85, the first number is the bore, which is the inside diameter of the cone or inner ring. This is the surface that fits over the shaft or pinion journal. The second number is the outside diameter, measured across the cup or outer ring, and this is the surface that fits into the housing bore. Those two surfaces sit on different sides of the bearing, so each figure answers a different fitting question. A 55 mm bore tells a technician what the shaft must measure; an 85 mm outside diameter tells a technician what the housing opening must measure. Width and total assembly height are separate terms. Width describes the axial thickness of the cone and cup, often shown as separate values in a tapered roller bearing manufacturer catalog. Total assembly height describes the axial space the mounted bearing set occupies once the cup and cone sit against their shoulders. On a single-row tapered roller bearing, the cup and cone are separable components, and the contact angle means the axial position matters as much as the radial fit. A tapered roller bearing catalog may list bore and outside diameter first, but the axial figures are what make the size chain usable for assembly. The published listing for F-806149.03. TR1 gives a 55 mm bore and an 85 mm outside diameter for a single-row tapered roller bearing listed for automobile use, with a 0.40 kg unit weight. Those are nominal boundary dimensions: they describe the intended boundary size of the part, not the exact reading from a worn raceway. Width and total assembly height sit outside the published listing, so the size chain stops at two boundary dimensions. That is enough to identify the part family and start a size comparison, while the axial figures still need to come from a drawing, a supplier dimension sheet, or a physical check against the housing stack.

Reading Bore and Outside Diameter with a Caliper or Micrometer

A bench check is simple when the part is clean and the instrument is zeroed. The goal is not to prove the part is good or bad from one reading; the goal is to attach a real number to the bore and outside diameter, then compare those numbers with the published boundary size. A worn raceway can read slightly under nominal, so the technician should note the actual value, the measurement direction, and the condition of the contact surface.

  1. Clean and seat the part. Wipe grease and grit from the bore and the cup face, then set the bearing on a clean bench so it sits square. Dirt on a caliper jaw or under the cup face adds error to the reading, and a part resting at an angle can make a good bore look oval. Clean handling also protects the roller surfaces during measurement.
  2. Measure the bore in two directions. Use the inside jaws of a caliper or an inside micrometer across the cone bore, roughly 90 degrees apart, near the middle of the bore. Two directions reveal ovality or a worn patch that a single reading can hide. On a used bearing, the bore may read a few hundredths under the nominal 55 mm figure because of wear, handling marks, or a light interference fit history.
  3. Measure the outside diameter across the cup. Close the caliper or micrometer across the cup outside diameter, again in two directions, keeping the contacts on the cup surface rather than on the cage or rollers. The cup is the outer ring, so this reading answers the housing-fit question. A micrometer is the better choice for a final comparison because it controls contact force and gives a steadier reading on a curved surface.
  4. Record the readings against the nominal figures. Write down the actual bore and outside diameter values, the instrument used, and any visible wear pattern. Compare them with the published 55 mm and 85 mm figures for F-806149.03. TR1, then mark whether each reading sits above, below, or on the nominal size. A reading taken on a worn raceway describes the condition of that part; it does not replace the nominal size for a replacement search.

The two-direction habit matters because bearings wear unevenly. A bore can look correct at one point and show a low spot 90 degrees away, and a cup can show a similar pattern after a long service run. A caliper is fine for a quick sort, while a micrometer gives better repeatability when the reading will be used for a parts decision. The final record should show the nominal figures, the measured figures, and the condition note together, because a single worn reading can send a technician toward the wrong replacement size.

Why a 55x85 Size Cannot Confirm Installation Clearance by Itself

Installation clearance is a system result, not a single bearing dimension. The 55 mm bore and 85 mm outside diameter fix the radial boundary surfaces, but the axial stack decides how far the cone and cup sit into the housing. The cup shoulder, housing shoulder, spacer, and shaft shoulder all influence the final position. A bearing that matches the bore and outside diameter can still sit at the wrong depth if the cone width, cup width, or total assembly height differs from the original stack. That is why the 55x85 pair is a starting filter for a parts search, not a complete assembly check. The published F-806149.03. TR1 record confirms the 55 mm bore, the 85 mm outside diameter, the 0.40 kg weight, and the single-row automobile bearing description. Width and total assembly height are absent from that record, and chamfer, tolerance class, and load ratings are not published either. Those details affect how the part seats, how the shaft fit behaves, and how much axial space the assembly needs. A technician comparing a removed bearing with a listing should keep the measured bore and outside diameter as condition evidence, while treating the nominal 55 mm and 85 mm figures as the published boundary size. The practical reading order is therefore: match the bore to the shaft surface, match the outside diameter to the housing bore, then look for the axial width and total assembly height in the drawing or dimension sheet. If those axial figures are not available, the size callout remains a partial match. For an automobile tapered roller bearing, the assembly position and shoulder contact matter as much as the two headline numbers. A 55x85 reading narrows the search quickly, and the full installation decision needs the axial dimensions that sit beside those two figures.

Conclusion

Reading a 55x85 tapered roller bearing size is mostly a matter of attaching each number to the right surface. The 55 mm figure is the bore, the 85 mm figure is the outside diameter, and width plus total assembly height are separate axial terms. For F-806149.03. TR1, the published listing gives the 55 mm bore, 85 mm outside diameter, and 0.40 kg weight for a single-row automobile bearing, while the axial figures remain outside that listing. A technician who records the measured bore and outside diameter, then asks for the width and assembly height before reassembly, avoids the common mistake of treating two radial figures as a full installation match. The next useful step is to compare the measured values with the published boundary size and confirm the axial stack against the housing.

FAQ

Q: What does 55x85 mean on a tapered roller bearing?

A: It is shorthand for a 55 mm bore and an 85 mm outside diameter. On a tapered roller bearing, the bore is the inside diameter of the cone, and the outside diameter is measured across the cup. Those are nominal boundary dimensions, while width and total assembly height are separate figures that belong to the axial stack.

Q: Is 55 mm the inner diameter or the outer diameter?

A: The 55 mm figure is the inner diameter, also called the bore. It is the inside surface of the cone that fits over the shaft or journal. The 85 mm figure is the outside diameter across the cup, which is the surface that fits into the housing bore.

Q: Can a bearing with a 55 mm bore and 85 mm outside diameter suit a different assembly width?

A: Yes, when the housing and shaft stack are built for that bearing's axial width and total assembly height. The 55x85 pair fixes only the bore and outside diameter. A different assembly width can work if the cone width, cup width, shoulder positions, and spacer arrangement match the new assembly. The width and total assembly height must come from the drawing or dimension sheet.

Sources / References

Motion + Power Manufacturers Alliance

Basic Bearing Knowledge | Koyo Bearings / JTEKT CORPORATION

Related Examples

F-806149.03.TR1 Automobile Bearing F-806149.03 Roller Bearing 806149 - Stock for Sale

Precedente
How to Cross-Reference F-806149.03.TR1 with 806149 Bearings
Per saperne di più
Il prossimo
Tapered Roller Bearings Carry Combined Loads in Car Drivetrains
Per saperne di più